The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

The Allureglow USA SB-2045-RR Series Reflective Inks are Premium Air Dry Solvent Based  Reflective Screen Printing Inks, designed for Printing on Flexible Vinyl, Rigid Vinyl, Acrylic, Plastics, Styrene, Coated Papers, Coated Paper and Card Stock. These Inks look like conventional colors in normal light and have remarkable reflective properties when light is shined on it. This Ink is an excellent enhancement to any Print with its increased visibility.  

Directions and Helpful Information:

All SB-2045-RR Series Inks are Ready to Use Inks, however it is extremely important that they be properly mixed prior to use. Mixing should be done with a High Speed Drill or Drill Press using a Type 2 Dispersion Blade. Continue to Mix Ink occasionally throughout the Print Production Run.

Keep lids on containers to avoid contamination and drying of the Ink.

In warmer climates and environments, do not allow the Inks to sit idle on the Screens. If you must stop printing, Remove any excess Ink and Clean the Screen and Squeegee with Eco-Friendly Screen Cleaner/Opener or Press Wash to prevent screens from drying out and clogging up. Remember these are an Air Dry Type Ink.

Do Not Mix SB-2045-RR Series Inks With Any Other Inks or Color Concentrates

For Best Results: Use Lite to Medium Flood and Lite to Moderate Squeegee Pressure on both Automatic  and Manual Presses

The SB-2045-RR Series Reflective Inks should be Printed using a Single Pass and 110 to 160 Mesh Screens, depending on the color and amount of reflectivity you are trying to achieve and the Type of Screens, Emulsion and Emulsion Thickness you are using.  

Drying & Curing Inks: Finished Prints should be placed on a Drying Rack to Dry for a total of 24 hours. The Inks are Dry to the touch after 30-45 minutes @70ºF (21ºC)

Always perform adhesion test once Ink has Cured for 24 Hours.

Clean-Up can be done using Eco-Solvents or Safety-Kleen Tank

Testing and viewing can be best done in a dark room or hallway, place print at least 10 feet away from you on a wall, place a good flashlight between you eyes and point at the print, the light should reflect back at the viewer.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.  

For additional Information Call (888) 493-4569 or email Info@allureglowusa.com

 

AA-1000-CC Clear Top Coat For AA Series Safety & Fluorescent Paints IN A FIVE GALLON KIT.

Allureglow USA AA-1000-CC Clear Top Coat Kit is a waterborne, self-crosslinking high solids 100% acrylic coating. It exhibits exceptional light clarity when cured, and has a high UV resistance and produces a hard but flexible coating. To be used as a Top Coat for application to Allureglow USA AA Series Safety Paints.

Includes a 10oz bottle of AG-CLA-100 to be added at a rate of 2 Ounces Per Gallon of AA-1000-CC

NOTE: There is a Special Handling Fee Included in the price for this paint in this size container.

AA-1000-CC Clear Top Coat for All AA Series Safety  and Fluroescent Paints IN A ONE GALLON KIT

Allureglow USA AA-1000-CC Clear Top Coat Kit is a waterborne, self-crosslinking high solids 100% acrylic coating. It exhibits exceptional light clarity when cured, and has a high UV resistance and produces a hard but flexible coating. To be used as a Top Coat for application to Allureglow USA AA Series Safety Paints and Fluorescent Paints

Includes a 2oz bottle of AG-CLA-100 to be added at a rate of 2 Ounces Per Gallon of AA-1000-CC

AA-1000-CC Clear Top Coat for All AA Series Safety  and Fluroescent Paints IN A ONE QUART KIT

Allureglow USA AA-1000-CC Clear Top Coat Kit is a waterborne, self-crosslinking high solids 100% acrylic coating. It exhibits exceptional light clarity when cured, and has a high UV resistance and produces a hard but flexible coating. To be used as a Top Coat for application to Allureglow USA AA Series Safety Paints and Fluorescent Paints

Includes a 2oz bottle of AG-CLA-100 to be added at a rate of 2 Ounces Per Gallon of AA-1000-CC

AA-1000-WP White Primer FOR ALL AA-SERIES Photoluminescent/Glow in the Dark Paints.

IN A FIVE GALLON SIZE.

 NOTE: There is a Special Handling Fee Included in the price for this paint in this size container.

AA-1000-WP White Primer FOR ALL AA-SERIES Photoluminescent/Glow in the Dark Paints.

IN A GALLON SIZE.

White Primer FOR ALL AA-SERIES Photoluminescent/Glow in the Dark Paints.

IN A FIVE GALLON SIZE.

The HS-1000-FL-BB is a Fluorescent Blue High Solids Acrylic Screen Printing Ink. This unique Ink has a Neon or Fluorescent Blue Color in normal light and emits a vibrant Blue when exposed to Blacklights. PACKAGED IN A FIVE GALLON CONTAINER 

NOTE: There is a Special Handling Fee Included in the price for this size container.

This Allureglow USA HS-1000-FL Ink is a Premium High Solids Acrylic, PVC Free, Fluorescent Screen Printing Ink, designed for Cotton & 50-50 and with the use of our AG-CLA-100 Additive you can print on Polyester, Nylon and Stretch Fabrics and much more. This unique Ink looks like conventional colors in normal light and has remarkable glow properties when in darkness. This Ink is an excellent enhancement to any garment that increased visibility would be a benefit.

Directions and Helpful Information:

The Allureglow USA HS-1000-FL is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA-100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Color Quality by not doing so.

For Best Results A Moderate Flood and Medium to Moderate Squeegee Pressure on Automatic Presses and Moderate Flood and Medium to Moderate Squeegee Pressure on Manual Presses is recommended.

Allureglow USA HS-1000-FL can be printed using 110-305 Mesh Screens depending on the color of the Ink and Garment

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

For best long term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

The HS-1000-FL-BB is a Fluorescent Blue High Solids Acrylic Screen Printing Ink. This unique Ink has a Neon or Fluorescent Blue Color in normal light and emits a vibrant Blue when exposed to Blacklights.

PACKAGED IN A ONE GALLON CONTAINER 

This Allureglow USA HS-1000-FL Ink is a Premium High Solids Acrylic, PVC Free, Fluorescent Screen Printing Ink, designed for Cotton & 50-50 and with the use of our AG-CLA-100 Additive you can print on Polyester, Nylon and Stretch Fabrics and much more.

Directions and Helpful Information:

The Allureglow USA HS-1000-FL is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA-100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Color Quality by not doing so.

For Best Results A Moderate Flood and Medium to Moderate Squeegee Pressure on Automatic Presses and Moderate Flood and Medium to Moderate Squeegee Pressure on Manual Presses is recommended.

Allureglow USA HS-1000-FL can be printed using 110-305 Mesh Screens depending on the color of the Ink and Garment

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

For best long term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

The HS-1000-FL-BB is a Fluorescent Blue High Solids Acrylic Screen Printing Ink. This unique Ink has a Neon or Fluorescent Blue Color in normal light and emits a vibrant Blue when exposed to Blacklights.

PACKAGED IN A ONE QUART CONTAINER 

This Allureglow USA HS-1000-FL Ink is a Premium High Solids Acrylic, PVC Free, Fluorescent Screen Printing Ink, designed for Cotton & 50-50 and with the use of our AG-CLA-100 Additive you can print on Polyester, Nylon and Stretch Fabrics and much more.

Directions and Helpful Information:

The Allureglow USA HS-1000-FL is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA-100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Color Quality by not doing so.

For Best Results A Moderate Flood and Medium to Moderate Squeegee Pressure on Automatic Presses and Moderate Flood and Medium to Moderate Squeegee Pressure on Manual Presses is recommended.

Allureglow USA HS-1000-FL can be printed using 110-305 Mesh Screens depending on the color of the Ink and Garment

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

For best long term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com  

TECHNICAL DATA

The HS-1000-FL-CL is a Fluorescent Clear High Solids Acrylic Screen Printing Ink. This unique Ink has a Clear or No Color in normal light and emits a vibrant Blue when exposed to Blacklights.

PACKAGED IN A FIVE GALLON CONTAINER

NOTE: There is a Special Handling Fee Included in the price for this size container.

This Allureglow USA HS-1000-FL Ink is a Premium High Solids Acrylic, PVC Free, Fluorescent Screen Printing Ink, designed for Cotton & 50-50 and with the use of our AG-CLA-100 Additive you can print on Polyester, Nylon and Stretch Fabrics and much more.

Directions and Helpful Information:

The Allureglow USA HS-1000-FL is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA-100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Color Quality by not doing so.

For Best Results A Moderate Flood and Medium to Moderate Squeegee Pressure on Automatic Presses and Moderate Flood and Medium to Moderate Squeegee Pressure on Manual Presses is recommended.

Allureglow USA HS-1000-FL can be printed using 110-305 Mesh Screens depending on the color of the Ink and Garment

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

For best long term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com  

TECHNICAL DATA