AA-1000-FL-VV  AA SERIES VIOLET FLUORESCENT PAINT 100% ACRYLIC WATERBASED IN A ONE QUART CONTAINER

The Allureglow USA AA Series Fluorescent/Blacklight Paints are designed for Special Effects, Stage and Theater Sets and really anywhere you are looking to Highlight or Enhance the setting when UV or Blacklights are present. These Paints are formulated using the Highest Quality Fluorescent Pigments available, which greatly enhance the vibrancy of all the Colors we offer. These Paints are 100% Acrylic, Low VOC and Waterbased for easy clean up. The AA Series Fluorescent Paints can be Brushed, Rolled or

Sprayed Applied. Because these paints are transparent, use our AA-1000-WP White Primer or Underbase prior to applying the AA-1000-FL Color, not doing so will result in the loss or poor vibrancy of the Color. When applying, use 2-3 Lighter Coats for Best Results.

The AA Series Fluorescent Paints are proudly manufactured in the USA

Available in Quarts, Gallons and Five Gallon Containers

Any application not referenced in the Technical Data Sheet should be pre-tested prior to any application.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.

Click on the link to download the Paint Technical Data Sheet 

Click on the link to dowlaod the Paint Safety Data Sheet

Click on the link to download the Paint Brochure

AA-1000-FL-YY  AA SERIES YELLOW FLUORESCENT PAINT 100% ACRYLIC WATERBASED IN A ONE QUART CONTAINER

The Allureglow USA AA Series Fluorescent/Blacklight Paints are designed for Special Effects, Stage and Theater Sets and really anywhere you are looking to Highlight or Enhance the setting when UV or Blacklights are present. These Paints are formulated using the Highest Quality Fluorescent Pigments available, which greatly enhance the vibrancy of all the Colors we offer. These Paints are 100% Acrylic, Low VOC and Waterbased for easy clean up. The AA Series Fluorescent Paints can be Brushed, Rolled or

Sprayed Applied. Because these paints are transparent, use our AA-1000-WP White Primer or Underbase prior to applying the AA-1000-FL Color, not doing so will result in the loss or poor vibrancy of the Color. When applying, use 2-3 Lighter Coats for Best Results.

The AA Series Fluorescent Paints are proudly manufactured in the USA

Available in Quarts, Gallons and Five Gallon Containers

Any application not referenced in the Technical Data Sheet should be pre-tested prior to any application.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application.

Click on the link to download the Paint Technical Data Sheet 

Click on the link to dowlaod the Paint Safety Data Sheet

Click on the link to download the Paint Brochure

HS-2045-AGB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Pale Green Daytime Color and Aqua Glow Color.

This Allureglow HS-2045-AGB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Single Component Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-AGB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Pale Green Daytime Color and Aqua Glow Color.

This Allureglow HS-2045-AGB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Single Component Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-AGB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Pale Green Daytime Color and Aqua Glow Color.

This Allureglow HS-2045-AGB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Single Component Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-BLKG This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Black Daytime Color and Green Glow Color.

This Allureglow HS-2045-BLKG Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-BLKG This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Black Daytime Color and Green Glow Color.

This Allureglow HS-2045-BLKG Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Single Component Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Black Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-BLKG Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-BLKG This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Black Daytime Color and Green Glow Color.

This Allureglow HS-2045-BLKG Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-FL-BB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Blue Daytime Color and Blue Glow Color.

This Allureglow HS-2045-FL-BB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-BB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Blue Daytime Color and Blue Glow Color.

This Allureglow HS-2045-FL-BB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-BB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Blue Daytime Color and Blue Glow Color.

This Allureglow HS-2045-FL-BB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-GG is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Green Daytime Color and Green Glow Color.

This Allureglow HS-2045-FL-GG Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-GG This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Green Daytime Color and Green Glow Color.

This Allureglow HS-2045-FL-GG Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-GG is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Green Daytime Color and Green Glow Color.

This Allureglow HS-2045-FL-GG Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-MM This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Magenta Daytime Color and Magenta Glow Color.

This Allureglow HS-2045-FL-MM Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-MM This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Magenta Daytime Color and Magenta Glow Color.

This Allureglow HS-2045-FL-MM Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-MM This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Magenta Daytime Color and Magenta Glow Color.

This Allureglow HS-2045-FL-MM Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-OO is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Orange Daytime Color and Orange Glow Color.

This Allureglow HS-2045-FL-OO Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-OO This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Orange Daytime Color and Orange Glow Color.

This Allureglow HS-2045-FL-OO Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-FL-OO This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a  Fluorescent Orange Daytime Color and Orange Glow Color.

This Allureglow HS-2045-FL-OO Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA