This Allureglow USA PS-2045-WHTG Ink is a Non-Phathalate Soft Hand Glow in the Dark. The PS-2045-WHTG is manufactured using only Phthalate Free Plasticizers and is compliant with all State and Federal Regulations concerning Phthalates.
Allureglow PS-2045-WHTG Inks enable the screen printer to print on either light or dark 100% cotton garments. The ink can also be used on other fabrics and vinyls with the addition of our AG-CLA100 Additive. Consult SDS prior to using. Phthalate Free Plastisol Glow in the Dark Screen Printing Ink. This PS-2045-WHTG Ink has a White Daytime and Green Glow Color. Check out our Allureglow USA Color Concentrates or our Fluorescent Pigments to make your own cool colors.
PACKAGED IN A FIVE GALLON CONTAINER
This Allureglow USA PS-2045 Ink is a Non-Phthalate Soft Hand Glow in the Dark Screen Printing Ink. The PS-2045 is manufactured using only Phthalate Free Plasticizers and is compliant with all State and Federal Regulations concerning Phthalates.
Allureglow PS-2045 Glow in the Dark Inks enable the screen printer to print on either Light or Dark Garments, providing a White Underbase or Discharge Underbase is done first. This Ink can also be used on other fabrics and vinyls with the addition of our AG-CLA-100 Additive. Consult SDS prior to using.
Directions and Helpful Information:
The Allureglow USA PS-2045 is a Single Component Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.
Keep lids on containers to avoid contamination of the Ink
If Ink is to thin for larger opening screens, the use of Allureglow USA LTS-1959 Thickner at a rate of 1/2% by Weight of Ink, Mix Throughly and Allow the Ink to Sit for 2-4 Hours Prior to Using.
The. use of a Lint Catcher or Overcoat Clear for dark fabrics will aid in uninterrupted production and reduce fibrillation. Create a single screen by combining all of the colors in the image to be printed on a dark 100% cotton fabric. Print using a suitable Primer Clear through a 230 mesh count and then flash cure.
YOU MUST USE A WHITE UNDERBASE OR PRINT ON ALL GRAMENTS OTHER THAN WHITE. YOU WILL GREATLY REDUCE THE GLOW INTENSITY BY NOT DOING THIS STEP.
For Best Results A Heavy Flood and Low to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Low to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the Highest Glow Intensity and Best Results
Allureglow USA PS-2045 can be printed using 86-180 Mesh Screens depending on the color and amount of glow you are trying to achieve.
Cure Ink at a Minimum of 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.
Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.
Clean-Up can be done using Bio-Degradable Screen Wash
For best long term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.
Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.
SEE OTHER SIDE FOR GLOW TESTING PROCEDURE
Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com
