The HS-1000-FL-YY is a Fluorescent Yellow High Solids Acrylic Screen Printing Ink. This unique Ink has a Neon or Fluorescent Yellow Color in normal light and emits a vibrant Yellow when exposed to Blacklights.

PACKAGED IN A ONE GALLON CONTAINER 

This Allureglow USA HS-1000-FL Ink is a Premium High Solids Acrylic, PVC Free Glow in the Dark Screen Printing Ink, designed for Cotton & 50-50 and with the use of our AG-CLA-100 Additive you can print on Polyester, Nylon and Stretch Fabrics and much more.

Directions and Helpful Information:

The Allureglow USA HS-1000-FL is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA-100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Color Quality by not doing so.

For Best Results A Moderate Flood and Medium to Moderate Squeegee Pressure on Automatic Presses and Moderate Flood and Medium to Moderate Squeegee Pressure on Manual Presses is recommended.

Allureglow USA HS-1000-FL can be printed using 110-305 Mesh Screens depending on the color of the Ink and Garment

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

For best long term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

The HS-1000-FL-YY is a Fluorescent Yellow High Solids Acrylic Screen Printing Ink. This unique Ink has a Neon or Fluorescent Yellow Color in normal light and emits a vibrant Yellow when exposed to Blacklights.

PACKAGED IN A ONE QUART CONTAINER 

This Allureglow USA HS-1000-FL Ink is a Premium High Solids Acrylic, PVC Free, Fluorescent Screen Printing Ink, designed for Cotton & 50-50 and with the use of our AG-CLA-100 Additive you can print on Polyester, Nylon and Stretch Fabrics and much more.

Directions and Helpful Information:

The Allureglow USA HS-1000-FL is a Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA-100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Color Quality by not doing so.

For Best Results A Moderate Flood and Medium to Moderate Squeegee Pressure on Automatic Presses and Moderate Flood and Medium to Moderate Squeegee Pressure on Manual Presses is recommended.

Allureglow USA HS-1000-FL can be printed using 110-305 Mesh Screens depending on the color of the Ink and Garment

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

For best long term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

TECHNICAL DATA

HS-2045-AGB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Pale Green Daytime Color and Aqua Glow Color.

This Allureglow HS-2045-AGB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Single Component Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-AGB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Pale Green Daytime Color and Aqua Glow Color.

This Allureglow HS-2045-AGB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Single Component Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com

HS-2045-AGB This is a High Solids Acrylic Photoluminescent/Glow in the Dark Screen Printing Ink, with a Pale Green Daytime Color and Aqua Glow Color.

This Allureglow HS-2045-AGB Screen Printing Ink is a Premium High Solids Acrylic, PVC Free, Ready to Use Formula, designed for printing on Cotton, 50-50, Polyester, Stretch Fabrics and many more fabrics. For those Screen Printers who have hard to adhere to Fabrics to print on, we offer a Low Temperature Cure and Adhesion Promoter Additive AG-CLA100. This unique Ink looks like a Pale Green Color in normal light and has incredible Photoluminescent/Glow in the Dark  properties when the print is placed in the dark. This HS-2045-AGB Ink is an excellent enhancement to any garment with it’s cool Photoluminescent/Glow in the Dark.

Directions and Helpful Information:

The Allureglow USA HS-2045 is a Single Component Ready to Use Ink, just mix it up and it is ready to use. Mixing should be done with a high speed drill or drill press using a Type 2 Dispersion Blade. Continue to mix Ink occasionally throughout production run.

Keep lids on containers to avoid contamination and drying of the Ink.

Note: You Must Use the AG-CLA100 at an addition rate of 1.5% by weight added to the Ink when printing on Polyesters, Nylon Lycra and Performance Fabrics.  This enables you to reduce curing temperatures to 280ºF (138ºC). Wash Tests Must Not Be Done Until 48 Hours After Curing.

Use of a White Underprint is a must on Dark Garments. You will sacrifice Glow Intensity and Longevity by not doing so.

For Best Results A Heavy Flood and Slow to Moderate Squeegee Pressure on Automatic Presses and Heavy Flood and Light to Moderate Squeegee Pressure on Manual Presses is recommended. A Print /Flash/Print Method will achieve the best results

Allureglow USA HS-2045 can be printed using 86-200 Mesh Screens depending on the color and amount of glow you are trying to achieve.

Cure Ink at 320°F (160°C) Always Test Dryer Temperatures prior to and during production. Curing Time will be between 90 to 180 seconds, depending on amount of ink deposit and color of garment.

Always perform wash test prior to production, to ensure proper adhesion to the fabric, prior to production runs.

Clean-Up can be done using Soap & Water

Testing and viewing can best be done in a dark room, after charging the print in sunlight for 10 minutes or under artificial light for 30 minutes. Always allow your eyes to adjust for a few minutes after entering the dark room.

For best long-term durability wash in cold water on the delicate cycle and wash inside out. Do Not Use Bleach. Do Not Iron on Print. Line or Hang Dry.

Any application not referenced in this Technical Data should be pre-tested prior to any production run is done.

Manufactured By: Allureglow USA and Allureglow USA makes no representation as to the suitability of any given products; it is up to the buyer or user to determine if the product is suitable for the given application. (888) 493-4569 or www.allureglowusa.com